Beginners Guide to Troubleshoot with Netgear Nighthawk Router LEDs

 Netgear Nighthawk has various LEDs on it that indicates the status of connection between your router and the devices connected to it. At times, the LEDs on Netgear Nighthawk router start blinking or turn off suddenly and results in connectivity issue. 4 out of 5 users don’t know the reason behind blinking or no LEDs on their Netgear Nighthawk router. If you are also one of them, then we have come up with this post to troubleshoot with the LEDs on your Netgear Nighthawk router. Let’s start over!

Note: The LEDs vary upon the model number of Netgear Nighthawk router you are using. Besides, ensure that you have gone through the NetgearGenie setup instructions once.


Fix: Netgear Nighthawk Router LEDs


Netgear Nighthawk Orange Light

Netgear Nighthawk orange color LED is one of the most common issues faced by a user across the globe. If you are also facing the same issue and looking for a solution, then do the following:

  • Power-cycle your Netgear Nighthawk router. For this, you have to unplug the device for a couple of minutes and after that, plug it back again.
  • Check the status of your existing modem or gateway. Chances are, you have lost the internet connection. For this, have a word with your ISP regarding the same.
  • Make sure that you have done the Netgear Nighthawk setup process properly. Improper or incomplete Netgear router setup might results in the error.



Netgear Nighthawk Router Internet LED Blinking White

This color LED indicates that your Netgear Nighthawk router has failed to connect to your modem. To fix it, consider the Netgear router troubleshooting steps given below.

  • Disconnect your modem and the router from the wall socket.
  • Keep then disconnected for a 10-25 minutes. Till then, have a cup of tea or coffee or you can also opt for a chilled beer.
  • Then, power them on again. Turn on your modem first and after two minutes, turn on your Netgear Nighthawk router.

Now, check whether this issue is fixed or not. In the event the same issue is annoying you, ask your ISP if you are getting the actual internet speed you are paying for or not.


Netgear Nighthawk Red LED

This is the most annoying issue. When we see red color LED on our device, we get really worried. If you are also hit by the red color LED on your device, then without wasting much time, have a look at the troubleshooting steps given below.

  • Ensure that your Netgear Nighthawk router is properly plugged in and receiving uninterrupted power supply.
  • If so, the power off your Netgear router and turn it on after a few seconds.
  • Make sure that you have setup the device using correct Netgear Nighthawk login details.
  • Be sure that you have updated Netgear router firmware.
  • Make sure that your Netgear Nighthawk router is placed at the middle location of your house. In order to get the most out of your Netgear Nighthawk router, do not ground it or place it inside cabinet or back of anything.


Netgear Nighthawk Blinking Blue LED

The blue color LED on your Netgear Nighthawk router indicates that your device is still booting up. But you don’t have to worry at all. We have provided accurate fixes for this issue also.

  • Make sure that your modem is compatible with the Netgear Nighthawk router. If your modem is too old, ask your ISP to replace it.
  • Ensure that your router isn’t in booting status.
  • Be sure that your router isn’t overcrowded with unknown devices. For this, you can limit the number of connected device using the “Guest Access” feature of Netgear router app.
  • Reset Netgear router back to factory default values.

Our guide to troubleshoot with Netgear Nighthawk router LEDs ends here. If you still have any difficulty in following the fixes given in this post, contact our experts right away.